Golden-lighting 1208-3P DNI Uživatelský manuál stáhnout pdf

Assembly Instructions: 1208-3P DNI (Marcellis)

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

PREPARING FOR INSTALLATION

Carefully remove all of the contents from the carton. See the

important notes above. Shut off the power at the circuit breaker

andcompletelyremovetheoldxturefromthewall,including

theoldmountingstrap.

Fromthepartsbagremovethemountingstrapassembly.One

endofnipple(F)shouldbeattachedtomountingstrap(A)with

washerandhexnuts(C&D)inplace.Theotherendshouldhave

canopy loop (H) attached.

Attachmountingstrap(A)tothejunctionboxusingmounting

screws(B)andascrewdriver.Tightensecurely.Unscrewcanopy

loop collar (I) from canopy loop (H). Pass canopy (G) over the

mountedcanopylooptotesttheheight.Approximatelyhalf

ofthecanopyloop’sexteriorthreadsshouldbeexposed,and

thecanopyloopcollarshouldtsnuglyontothecanopyloop.

Removecanopy(G)andadjusttheheightofnipple(F)and

canopyloop(H)untilthedesiredheightisreached.

Bymeasuring,determinethecorrectamountofchainandwire

neededforproperhangingheight.Ifnecessary,useapairof

plierstoopenandremoveanyexcesschain.Attachoneofchain

connectors(K)toeachendofchain(J).Passthexturewires

throughtoploop(H).Attachoneendofchain(J)totoploop(L)

usingchainconnector(K)andclosechainconnector(K).Attach

oneendofeachrod(O)todecorativehooks(N)onxturebody

(P). Use the free end of rod (O) to attach the rod to the hooks on

top cap (M). Use the free chain connector (K) to attach chain (J)

tocanopyloop(H).Feedthexturewiresupthroughthechain

(everythreelinksorso),pullingthewiresuntiltaut.Trimthewires

tothedesiredlengthplus8to10inches.

CONNECTING THE WIRES

Haveanassistantsupportthextureweightwhilecompleting

thewiring.Threadthexturewiresthroughcanopy(G).Attach

thexture’swirestothepowersupplywiresfromthejunction

box.Connectblacktoblack(orsmooth);whitetowhite(or

ribbed);groundtoground(greenorcopper).Twisttheendsof

thewirepairstogether,thentwistonawireconnector.Make

surealltwistsareinthesamedirection.Ifthereisnogroundwire

(greenorcopper)fromthejunctionbox,locategroundscrew(E)

onmountingstrap(B)andwrapthexturegroundwirearound

thegreengroundscrew(E).Useascrewdrivertosecureground

screw(E)ontothemountingbracket.Tuckallwiresneatlyinto

thejunctionbox.

FINISHING THE INSTALLATION

Note: Completetheremainingstepsafterthextureishung.

Tightenthedecorativehammerednials(T)ontothethreadsat

thebottomofthexturearms.

Carefullyslideglassshades(Q)oversockets(S).Candlesleeves

(R)haveretainingringsattached.Eachretainingringhastwo

smallholesineachside.Theglassshadeopeningistight.

Carefullypushthecandlesleevesdownintotheglassshades

and over the sockets. Carefully place the tips of socket tool (U)

intotheholesintheretainingring.Usesockettool(U)tothread

theretainingringsontothesocketthreads.Thiswillsecurethe

glassinplace.

Installlightbulbsinaccordancewiththexture’sspecications.

Donotexceedthemaximumrecommendedwattage.

Your installation is now complete. Turn on the power and test the

xture.

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

For Customer Service, contact

the place of purchase to arrange

for replacement parts.

BLACK

(Hot)

WHITE

(Neutral)

GREEN

(Ground)

HOUSE WIRES

SMOOTH

(Or Black)

FIXTURE WIRES

RIBBED

(Or White)

BARE COPPER

(Or Green)

Shrnutí obsahu

Strany 1 - FINISHING THE INSTALLATION

Assembly Instructions: 1208-3P DNI (Marcellis)IMPORTANT: • ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL. • SHUT OFF POWER SUPPLY

Komentáře k této Příručce

Žádné komentáře

Golden-lighting 1208-3P DNI Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Golden-lighting 1208-3P DNI. Golden Lighting 1208-3P DNI User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Golden-lighting 1208-3P DNI